BESTEK Dash Cam Hardwire Kit with Motion Detection Sensor, 12V

BESTEK Dash Cam Hardwire Kit with Motion Detection Sensor, 12V 24V to 5V/2A OBD-II Dash Cam Hardwire Kit with 9.4ft/2.85m Wire, Low Voltage Protection Compatible with Mini USB Dash Cams, GPS Navigator
- Wide Compatibility: This dash cam hardwire kit is suitable for most 12V and 24V vehicles, compatible with all the 2 amps input Mini USB（not for Micro USB） dash cam, mirror cam, GPS navigator and radar detector etc. Works with most of the APEMAN, CHORTAU, Vantrue, Nexar, Falcon, Aukey, VAVA and other Mini USB dash cam.
- Easy Setup: No extra electrical wiring or tools needed to install this kit, just plug into the OBD-II port. You can adjust the position of the 9.4ft/2.85m line at will to get the most comfortable installation.
- Wide Sensing Range: 19.7ft/6m long detection distance and in front 150° induction angle. Instantly turns on the dash cam when motion is detected, shuts off automatically within 30 seconds after motion is not detected.
- 24 Hours Surveillance: This kit uses international universal type OBD II port (with on/off power switch) instead of cigarette lighter port, which will release cigarette lighter for other electronic devices, can supply power for dash camera for 24 hours uninterruptedly. The motion detection function let your dash cam record when at needs. Built-in safeguards protect your device from overcurrent, overvoltage and overheating damage.
- Battery Drain Protection: This kit will continuous power your car devices, but when your vehicle’s battery voltage drops to 11.6V or 23.6V, the regulator will cut off the power, for the purpose to leave enough power to start up your engine, this also called Low Voltage Protection. You can also turn off the power switch if you don't need to record.
Product Description:
This dash cam hardwire kit suitable for 12V/24V vehicles, such as car, truck, bus, suvs, or big rig.
Can be used for all the 2 amps input Mini USB car devices, such as Dash Cams, GPS Navigator, Radar and Mirror Cam.
The OBD-II international standard port is commonly used for all the vehicles produced after 1996.
You can easily install the detection sensor onto your vehicleâ€™s front windshield with 3M adhesive pad, but please determine the location before installing.
0.3W max empty load loss under 12V voltage, 0.7W max empty load loss under 24V voltage. Efficiently save your vehicleâ€™s battery electricity with the low voltage protection system.

How to Set Up:
Step 1. Plug the male OBD port to your vehicleâ€™s female OBD port
Step 2. Fix the wire along the edge of the interior of your vehicle's compartment
Step 3. Choose a right position, use the with-in 3M adhesive pad to fix the motion detection sensor
Step 4. Plug Mini USB port into your dash cam
Step 5. Turn on the switch to power your dash cam
Â
Note:
OBD port location varies by vehiclesâ€™Â model, please find your OBD location first.
The mounting of the device and OBD cable should NOT interfere the normal operationÂ of the airbag.
Rain, snow, swaying tree branches or busy streets/parking lot environment, will sometimes cause the video recording continuously

Specifications:
Wire Lengthï¼š1.35ft/0.4m Output line Â Â 8.05ft/2.45m Input line
Motion Sensor Range: 19.7ft/6m, 150degree
Power Box Input: DC 12-30V
Power Box Output: 5V/2.5A
Low Voltage Protection: 11.6V under 12V / 12.6V under 24V
Country USA
Brand BESTEK
Manufacturer BESTEK
Binding Wireless Phone Accessory
ItemPartNumber BTALB10-BK
Size 9.4ft
EANs 6950334973744
ReleaseDate 0000-00-00

Country	USA
Brand	BESTEK
Manufacturer	BESTEK
Binding	Wireless Phone Accessory
ItemPartNumber	BTALB10-BK
Size	9.4ft
EANs	6950334973744
ReleaseDate	0000-00-00

BESTEK Dash Cam Hardwire Kit with Motion Detection Sensor, 12V 24V to 5V/2A OBD-II Dash Cam Hardwire Kit with 9.4ft/2.85m Wire, Low Voltage Protection Compatible with Mini USB Dash Cams, GPS Navigator

You might also like...