BGNing Openpilot CC3D Revolution Flight Controller Combo With

BGNing Openpilot CC3D Revolution Flight Controller Combo With M8N GPS Oplink Transceiver CC3D Power Distributors Plate Board For Drone FPV Multicopter
- Noted: The device of GPS for CC3D,NAZE32,SP Racing F3, Not include Compass. (The pictures of GPS device for "CC3D,NAZE32,SP Racing F3", showed"With Compass", In Fact - No Compass！ We do not want to make confusion to you)
- CC3D and NAZE32 Flight Controller devices are build-in Compass, They can not support external compass! This is why the GPS device do not include Compass. <br/>Please make clear and note this informaiton before ordering.
- Openpilot Has Been 32bit Since Day One, And The FPU Is Another Step Up The Performance Ladder
- The Revolution Is A Flight Control Computer With Autopilot, Intended For Multirotors, Helicopters And Fixed Wings. Technical Description CPU ,CPU Is The STM32F405RGT6 Chip, With ARM Cortex-M4 Core At 210MIPS, FPU, And Saturation Arithmetics DSP Functions
- All These Modules Can Be Configured For Accessing The Chip Pins Using A Flexible Switch Matrix, Or Disabled To Save Power;The Board Features A Built-In 433mhz Oplink Modem
Noted: The device of GPS for CC3D,NAZE32,SP Racing F3, Not include Compass.
(The pictures of GPS device for "CC3D,NAZE32,SP Racing F3", showed"With Compass", In Fact - No Compassï¼ We do not want to make confusion to you)
----- CC3D and NAZE32 Flight Controller devices are build-in Compass, They can not support external compass! This is why the GPS device do not include Compass.
Please make clear and note this informaiton before ordering.

Packing List:
CC3D Revolution With Flight Control Data Transmission Antenna * 1
OPLINK Ground Terminal With Data Transmission Antenna * 1
,M8N GPS * 1
CC3D Shielded Housing Sub-Plate * 1

All Cables Openpilot CC3D Revolution Flight Controller
Openpilot Products Use The Standard Openpilot Footprint, And Hence Has The Same Dimensions And Mounting Holes As The Openpilot CC. CC3D, Revo, GPS, OSD And Pipx Boards. Ports: - Servo 1-6: These Are The PWM Outputs That Go To Servos Or Electronic Speed Controllers (Escs).
Power For The Flight Controller Is Typically Supplied Through These Headers From Only One Of The Escs, But In Most Cases, All The Servo Wires Can Be Left Connected.
Cutting The Pin From Servo Wires Is Highly Discouraged.
If You Feel You Must Disconnect Three Of The Hot Wires, Use Some Shrink Tube Or Electrical Tape To Insulate The Removed Pin (You May Need That Positive Voltage At A Later Date!).
The Positive (Vcc) And Negative (Gnd) Pins Are Indicated On This Diagram And The Board. In Rare Cases, You May Need To Also Disconnect The Ground Pin If Your Escs Are Creating Ground Loop Problems (Indicated By A General Weirdness In Setup).
(See The Coptercontrol - CC3D -Atom Hardware Setup Page, Power Section, For Instructions On How To Remove And Insulate The Extra Pins)
Country USA
Binding Toy
Brand BGNing
EAN 0740030455660
IsAdultProduct
Label BGNing
Manufacturer BGNing
Publisher BGNing
Studio BGNing
ReleaseDate 0000-00-00

Country	USA
Binding	Toy
Brand	BGNing
EAN	0740030455660
IsAdultProduct
Label	BGNing
Manufacturer	BGNing
Publisher	BGNing
Studio	BGNing
ReleaseDate	0000-00-00

BGNing Openpilot CC3D Revolution Flight Controller Combo With M8N GPS Oplink Transceiver CC3D Power Distributors Plate Board For Drone FPV Multicopter

You might also like...