Biantie La 6A Rated 8mm LED Strip Connector, Solderless

Biantie La 6A Rated 8mm LED Strip Connector, Solderless Reusable 2 Pin Terminal for Single Color Tape Lights, 10 Pack White DIY Joiner for 22-20 AWG Wire, 12V 24V
- CONNECT AND RECONNECT WITHOUT RUINING YOUR STRIP — The flip-latch design clamps directly onto the copper pads of your 8mm LED tape light with even, controlled pressure - no piercing, no pad scraping, no destroyed sections. If you clip it on wrong-side-up or reverse the polarity (+/−), just lift the white latch, flip the strip, and try again. Many users find a solid connection on the first attempt; the latch design makes it forgiving when they don't.
- 6A RATING, FITS THE WIRES YOU ALREADY HAVE - Rated 6A at 5V-24V DC, these connectors designed to handle typical LED strip loads of most single-color LED strip runs helps reduce heat buildup at the joint. The wire slot accepts 22–20 AWG two-conductor cable — both solid and stranded — so you can use whatever extension wire is already on your shelf. Housing is made from flame-retardant polycarbonate. IP20 indoor-rated. Not for RGB, 10mm, or 12mm strips.
- BUILT FOR CABINET LIGHTING, SHELF STRIPS, AND EVERYWHERE IN BETWEEN — Clip onto LED tape inside kitchen cabinets, under bathroom vanities, along bookshelf edges, inside closet rods, beneath stair nosings, or behind TV panels — anywhere a soldering iron won't fit and a screw-tightening connector takes too long. No electrical license needed. Designed for homeowners doing weekend upgrades, renters who need non-destructive installs, and interior decorators setting up display case lighting.
- WORKS WITH IP65 WATERPROOF STRIPS - WITH ONE PREP STEP - For non-waterproof 8mm strips: insert and clip. For IP65 silicone-coated strips: use a small tool (e.g., fingernail or plastic tool) to peel back the silicone over the two copper pads, then insert — the exposed pads clamp solidly. These connectors are not compatible with: 10mm strips (5050 RGB), 4-pin or 5-pin strips, or any COB strip wider than 8mm. Suitable for renovation projects, rental apartment lighting swaps, studio lighting upgrades, and holiday display setups where you need connections you can take apart and reuse next season.
- COMPLETE YOUR LED LIGHTING SETUP IN ONE ORDER — These connectors are the link between your LED strip and your power supply or dimmer — you'll typically need them alongside 8mm single-color LED tape lights (2835 or 3528), a 12V or 24V DC power adapter, and 22–20 AWG two-conductor extension wire cut to your exact cabinet run length. If you're replacing lights in multiple rooms, we recommend picking up 20+ connectors — one for each cut section plus spares for polarity adjustments. Everything ships ready to clip, no tools required.
DIY Strip to Wire Quick Connection
Updated version of LED strip connectors, assemble wire by yourself as needed, flexible to different project! No need to solder. Just clasp your prepared led strip section into the connector to get connected. compatible with 30-120 LEDs/M strip, made of flame retardant material, safely use. Support high current LED strip lights.

Suitable for a variety of wire sizes
Stripping-free connectors usually have strict requirements on the wires, such as the standard wire 20 awg, 18 gauge can be well matched, and it is difficult to open again after closing.
These BL LED strip connector improves these shortcomings, 24 - 18awg standard or non-standard solid wire, stranded wire and fused wire can be applied. not only can be firmly clamped, but also easy to open and reuse.

Installation Tips:
Strip End:
1.Open the wire clip. It should snap open with just a little effort.
2.Insert your 8mm LED light strip inside the clip underneath the two contact prongs, making sure the + and - symbols align.
3.Snap the wire clip shut. Gently pull on the tape to confirm you've secured the strip inside the connector.
Wire End:
1.Separate 2 wires and stripping
2. Use a fingernail to press the two wires into the slot to clamp them.
3. Snap the wire clip shut. Pull on the wire to confirm you've secured the wires inside the connector.
If you have any problem about installation, pls feel free to contact me.

Package:
10pcs Strip to Wire Connectors (BL20B-8)
Country USA
Brand Biantie La
Manufacturer Alightings
Binding Kitchen
PartNumber BL20B-8
Model BL20B-8
Color White
Length 2
Weight 0.01984160358
Size small
NumberOfItems 10
ReleaseDate 0000-00-00

Country	USA
Brand	Biantie La
Manufacturer	Alightings
Binding	Kitchen
PartNumber	BL20B-8
Model	BL20B-8
Color	White
Length	2
Weight	0.01984160358
Size	small
NumberOfItems	10
ReleaseDate	0000-00-00

Biantie La 6A Rated 8mm LED Strip Connector, Solderless Reusable 2 Pin Terminal for Single Color Tape Lights, 10 Pack White DIY Joiner for 22-20 AWG Wire, 12V 24V

You might also like...