Crazepony CleanFlight BetaFlight Micro F3 Flight Controller

Crazepony CleanFlight BetaFlight Micro F3 Flight Controller Built-in PDB Buzzer Port 20X20mm For Mini FPV Racing 80 90 100 110 120 130 Drone
- Designed for Micro mini FPV Racers ------ The Microp F3 flight controller is specialy designed for mini FPV racing drone, generally sub 130 size, such as 80 90 10 110 120 130 class drone.
- Next-generation STM32 F3 processor ------ Utilizing the very latest F3 chip processor with built in CleanFlight BetaFlight firmware,STM32F3 microcontroller, with 256K bytes of flash memory, 3 hardware serial ports plus USB, and a floating point math coprocessor, a faster ARM-Cortex M4 core for fast control loop times
- Mini size Ultra light weight ------ 27*27mm ub suze and utilizes 20mm spacing with M3 mounting holes. Incorporating a high quality,gold plated, 4-layerr priented circuit board - all at a 2.7 all up weight.
- PDB ------ With an industry 1st gold plated PDB that is integrated within,this flight controller provides the ultimate in soldering ease with the highest grade of connectivity, allowing direct soldering points for motors, VTx, Receiver and FPV Camera
- Other features ------ Built-in 5V regulator(BEC), PDB Built-in, Oneshot Multi-shot ESC Support, Race Timing Transponder,MPU-6000 SPI-BUS, Built in LC Filter, Telemetry Support,Configurable,Micro USB Port, Broad RC Receiver Support,USE All Features at One Time, Reverse Current Protectoin, Programmable LEDs, Battery Monitoring, Buzzer,Serial Ports.
FEATURES
1. 27x27mm board with 20mm mounting M3 holes.
2. 2.6g with high-quality gold plated 4-layer printed circuit board.
3. Next-generation STM32 F3 processor with hardware floating point unit for efficient
flight calculations and faster ARM-Cortex M4 core.
4. Onboard regulator (BEC) 5V-2A for powering the FC, receiver and servos, camera. Direct
connection of up to 5s LiPo.
5. PDB build-in with support to Hex for SUB-130 size for very clean and easy setup (size andgt;
130 requires external PDB).
6. LC filter build-in for FPV camera.
7. Low-noise MPU-6000 SPI-bus gyro chip for faster acquisition of gyro data.
8. Pass-through ESC-BLHELI programming and config with UART1.
9. Battery voltage monitor.
10. Supports direct connection of SBus, SumH, SumD, Spektrum1024/2048,
XBus receivers. No external inverters required (built-in).
11. Dedicated SAT receiver interface with 3.3v using JST connector for compatibility with
Spektrum/LemonRC cables.
12. Dedicated PPM receiver input with 5V power.
13. 3 Serial Ports UART1, UART2, UART3 - NOT shared with the USB port.
14. Micro USB port.
15. Telemetry support.
16. LED strip support.
17. Buzzer port for audible warnings and notifications.
18. Flashing via USB or serial port.
19. Use all the features all the time. Connect your USB + OSD + SmartPort + SBus + GPS +
LED Strip + Battery Monitoring + Sonar + 6 motors - all at the same time.
20. Reverse current protection on LiPo and USB inputs for problem-free ESC calibrat

Package Including
1 * Micro flight controller

Country	USA
Binding	Toy
Brand	Crazepony
EAN	0190033484516
IsAdultProduct
Label	Crazepony
Manufacturer	Crazepony
MPN	4P175432LD2PI427
PartNumber	4P175432LD2PI427
Publisher	Crazepony
Size	small
Studio	Crazepony
ReleaseDate	0000-00-00

Crazepony CleanFlight BetaFlight Micro F3 Flight Controller Built-in PDB Buzzer Port 20X20mm For Mini FPV Racing 80 90 100 110 120 130 Drone

You might also like...