ECCPP Replacement fit for Keyless Entry Remote Control Car Key

ECCPP Replacement fit for Keyless Entry Remote Control Car Key Fob Nissan Infiniti Series KBRASTU15 (Pack of 2)
- 【ATTENTION】This listing is for Replacement Keyless Entry Remote with electronics and battery. The use and function will be the same as the original unit.
- 【REPLACEMENT】The Keyless Entry Kit with Interchange Part Number: KBRASTU15, CWTWB1U758, CWTWB1U821. Other Part Number: 28268-C991A, 28268-ZB700, 28268-C991C.
- 【FITMENT】The Keyless Car Remote is a replacement that fits for 03-09 Nissan 350Z, 02-06 Nissan Altima, 04-15 Nissan Armada, 02-06 Nissan Maxima, 03-07 Nissan Murano, 09-11 Nissan Pathfinder, 07-17 Nissan Sentra, 07-15 Nissan Versa, 04-09 Nissan Quest, 08-11 Infiniti EX35, 03-09 Infiniti FX35, 03-08 Infiniti FX45, 03-06 Infiniti G35, 02-04 Infiniti I35, 03-07 Infiniti QX56.
- 【INSTALLATION】Some vehicle DIY programming procedure is not available. These vehicles require a diagnostic equipment to be connected to the vehicle to program the remote. Please find local automotive locksmith or a dealer for programming. The steps of programming can be found here based on the your vehicle year, make and model. Programming Instructions: http://freeremoteinstructions.com or http://www.keyfobprogram.com or http://www.programyourremote.com
- 【SERVICE】If you have any questions about our Keyless Fob Replacement, please contact our friendly, helpful, and knowledgeable customer service representatives, we will be glad to address any questions or concerns promptly.
Fits For
03-09 Nissan 350Z
02-06 Nissan Altima
04-15 Nissan Armada
02-06 Nissan Maxima
03-07 Nissan Murano
09-11 Nissan Pathfinder
07-17 Nissan Sentra
07-15 Nissan Versa
04-09 Nissan Quest

08-11 Infiniti EX35
03-09 Infiniti FX35
03-08 Infiniti FX45
03-06 Infiniti G35
02-04 Infiniti I35
03-07 Infiniti QX56

How to Program the Key Fob Replacement
1. Close and lock all doors with the driver's side power lock switch located on drivers door panel.
2. Insert key into ignition (DON'T TURN) and remove it from the ignition key cylinder at least 6 times within 10 seconds (this will need to be done at approximately one second intervals).
You may need to insert and remove the key up to 10 or 12 times until your hazard lamps flash.
PLEASE NOTE: Withdraw key completely from ignition cylinder each time. If this procedure is performed too fast or too slow the system will not enter programming mode.

3. Insert key into ignition and turn to the ACC position.
4. Within 5 seconds, push the LOCK button on the keyless remote. Your hazard lamps will flash.
PLEASE NOTE: Do not press the button on the remote more than one time or the programming will not be successful.

5. If there are any remaining remotes (including working ones), Unlock then Lock all doors using the switch on drivers door panel.
Within 5 seconds of locking and unlocking doors press LOCK button on the next remote. Your hazard lamps will flash. Repeat this step for each remote (including any working remotes).
6. When all remotes have been programmed turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver's side power lock/unlock switch and open the driver side door.
--Finish all steps, Test all remotes--

Country	USA
Brand	ECCPP
Color	black
IsAutographed
IsMemorabilia
Label	ECCPP
Manufacturer	ECCPP
ManufacturerPartsWarrantyDescription	Parts
Model	4332964763
MPN	070727-5211-1133091
PartNumber	070727-5211-1133091
Publisher	ECCPP
Studio	ECCPP
ReleaseDate	0000-00-00

ECCPP Replacement fit for Keyless Entry Remote Control Car Key Fob Nissan Infiniti Series KBRASTU15 (Pack of 2)

You might also like...