Embroidex Cap/Hat Hoop for Brother Embroidery Machine SE270D

Embroidex Cap/Hat Hoop for Brother Embroidery Machine SE270D HE-120 900D HE-240 LB6770 SE400 LB6800PRW LB6800THRD 950D PE-450 PE500 HE1 SB7050E Simplicity SB7500 SE425 Innov-is 990D PE540D PE525 HE300
- ★ If you want to personalize caps and hats with designs such as logos, initials, names, you’ll need a cap hoop. The cap hoop attaches to your regular 4×4 inch hoop and holds the bill of the cap firmly in a clamp outside of the embroidery frame. The cap itself is attached to the hoop with adhesive stabilizer.
- ★ This Cap Hoop clamps to 4×4 inch embroidery hoops and will work with the Brother SE400, SE350, SE270D, HE120, HE240, Innovis 500D, Innovis 900D, Innovis 950D, LB6770PRW, LB6800PRW Embroidery Machines.
- ★ SE270D, PE-300S, HE-120, Innov-ís 900D, SE350, HE-240, LB6770, LB6770 PRW, SE400, LB6800PRW, LB6800THRD, Innov-ís 950D, PE-450, PE500, HE1, Simplicity SB7050E, Simplicity SB7500, SE425, Innov-is 990D, PE540D, PE525, HE300
How To Embroider A Cap With This Hoop Cut a piece of adhesive stabilizer slightly larger than the cap hoop frame and pull the backing off. Stick the stabilizer to the bottom frame of the cap hoop. Try wrapping the stabilizer around the edges of the cap hoop, if it doesn't stick tightly enough. Using a water-soluble pen, mark the center of the design on the cap. Loosen the back strap on the cap. Unscrew the thumbscrew on the hoop clamp to and slide the cap bill under the clamp. Using the markings you made on the cap and the template grid, arrange the cap so that the center of the design aligns with the center of the hoop. Before you tighten the clamp, make sure the sweatband and backing are pulled away from the embroidery area so that you don't stitch it to the cap. You may have to tape or pin the sweatband to keep it out of the way. The buckram (stiff backing) under the sweatband also has to be pulled back. If necessary to pull it back neatly, cut the buckram an inch or two where it is stitched to the cap bill on each side. Tighten the clamp with the thumbscrew. Starting in the middle and working out to the edges, press the cap down firmly against the adhesive stabilizer. The cap must be as flat and smooth as possible. Clamp the cap hoop to the regular 4×4 inch hoop on the side opposite where it attaches to the embroidery unit. Turn the SE400 on and set it up for embroidery as usual. Turn the embroidery unit on and attach the regular 4×4 inch hoop with the cap hoop attached. You may have to remove the foot and/or shank to do this. Use the curser keys to center the needle and begin to embroider your design onto the cap. Remember, the design must be rotated clockwise a quarter turn because the cap is hooped sideways and you want the design vertical.
Country USA
Brand Embroidex
Manufacturer Embroidex
Binding Kitchen
ItemPartNumber caphoopSe270d
Model 4336934073
UPCs 763985689614
EANs 0763985689614
ReleaseDate 0000-00-00

Country	USA
Brand	Embroidex
Manufacturer	Embroidex
Binding	Kitchen
ItemPartNumber	caphoopSe270d
Model	4336934073
UPCs	763985689614
EANs	0763985689614
ReleaseDate	0000-00-00

Embroidex Cap/Hat Hoop for Brother Embroidery Machine SE270D HE-120 900D HE-240 LB6770 SE400 LB6800PRW LB6800THRD 950D PE-450 PE500 HE1 SB7050E Simplicity SB7500 SE425 Innov-is 990D PE540D PE525 HE300

You might also like...