Geeetech Auto Level Sensor 3D Touch for DIY Prusa 3D Printer,

Geeetech Auto Level Sensor 3D Touch for DIY Prusa 3D Printer, greatly Improves Printing Accuracy (3D Touch Sensor)
- 【1】Simple: 3DTouch is easy to apply as it has a small and simple structure. Collecting information and firmware settings is a simple task, as 3DTouch works as a normal sensor for automatic bedding.
- 【2】Smart self-test: The push pin is pressed three times to test when the power is on. Alarm: The LED indicator flashes when a problem has been detected during a self-test or operation
- 【3】Compatibility: It is compatible with most Prusa I3 3D printers.
- 【4】Technologies: 3DTouch consists of Atmel ATtiny13A, an electromagnet and a pressure pin.
- 【5】Technical Support: We provide technical support and installation instructions. If you have any questions, please do not hesitate to contact us：Geeetech@qq.com
If you have any question, feel free to reach out to us:

FB: www.facebook.com/joeblackttt
Email: Geeetech@qq.com

Our 3d touch is on car leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D printer, and it is compatible with most Prusa I3 3D printers.

Note: 3D touch car leveling sensor is not plug_and_play; You may need some work on the connector. We have prepared the pins for you.

Specifications:
Voltage: 5V
Current: 15mA
Max. Current: 300mA
Cable length: 150mm
Net Weight: 10g
Shipping weight: 25g

Condition:
3DTouch can be operated in the following condition.
One I / O for control (PWM or Software PWM)
One I / O for Zmin (Z Probe)
GND and + 5V power

Wiring:
3-pin: Brown (-, GND), Red (+ 5V), Orange (control signal)
2-pin: Black (-, GND), White (Z min)

Caution:
Additional power supply will be needed in case your board does not supply enough amperage.
Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V (+) and GND (-)]
Pulling / pushing hard on the push pin damage 3DTouch and make it less accurate.
Fix push-pin with locking paint after reassembling or adjusting core.
Do not remove or deform the elastic material attached to the push pin.

Pack list:
1 X 3D Touch Car Leveling Sensor
1 X 3 Pin Straight Pin
1 X 2 Pin Straight Pin 2 X Screw & Nut & Washer
2 X Dupont Housing Shell 3 Pin
2 X Dupont Housing Shell 2 Pin
3 X Dupont Housing Shell 1 Pin
14 X Dupont Terminal
1 X 10K 1 / 8W resistor

If you have any question, feel free to reach out to us:

FB: www.facebook.com/joeblackttt
Email: Geeetech@qq.com
Country USA
Brand Geeetech
Label GEEETECH
Manufacturer GEEETECH
MPN 3D TOUCH SENSOR
PartNumber 3D TOUCH SENSOR
Publisher GEEETECH
Studio GEEETECH
ReleaseDate 0000-00-00

Country	USA
Brand	Geeetech
Label	GEEETECH
Manufacturer	GEEETECH
MPN	3D TOUCH SENSOR
PartNumber	3D TOUCH SENSOR
Publisher	GEEETECH
Studio	GEEETECH
ReleaseDate	0000-00-00

Geeetech Auto Level Sensor 3D Touch for DIY Prusa 3D Printer, greatly Improves Printing Accuracy (3D Touch Sensor)

You might also like...