JRTOOL EcoOBD2 Plug and Drive EcoOBD2 Benzine Chip Tuning Box

JRTOOL EcoOBD2 Plug and Drive EcoOBD2 Benzine Chip Tuning Box for Benzine 15% Fuel Save
- Ecoobd2 Plug and Drive EcoOBD2 Economy Chip Tuning Box for Benzine 15% Fuel Saving
- EcoOBD2 is the Cheap and Safe Type of Tuning.Remapping is a Permanent Change to Your Car. EcoOBD2 is Equipped with the Engine Protection Function and 100% Safe for Your Car Engine.
- EcoOBD2 Chip Tuning Box and Remapping Tuning Methods is that EcoOBD2 Chip Tuning Box is Easily Removable, and after Unplug You Go Back to the Factory Settings.
- It Works Based OBD2 Protocols as Remaping the Car's Computer ECU.
- After Driving 200 km Road Total, EcoOBD2 Adjusts Itself to the Car, According to the Drivers' Habits and Always Keeps Remaping the ECU to Save Fuel Lower and Immission.
What is EcoOBD2 Chip Tuning Box?
EcoOBD2 is a Chip Tuning Box which can be plugged into OBD2 connector of your car to decrease the fuel consumption of your car. When it plugged into OBD2 connector
EcoOBD2 receives the information from the car computer ECU. With the received data from ECU, EcoOBD2 adjusts the boost pressure, quantity of fuel, injection timing and pressure to decrease the fuel consumption of your car.
EcoOBD2 Chip Tuning Box does not exceed the manufacturer requirements. It works only within the tolerance of the engine.
EcoOBD2 does not damage the engine and the car computer ECU or not cause any negative effects to the car factory setting.
EcoOBD2 does not change any of the settings permanently. To turn back to the car's original settings, just unplug EcoOBD2 from OBD2 connector.

How to use?
Plug EcoOBD2 into OBD2 connector of your car. And turn the ignition on for 30 seconds. And Turn the engine on.
EcoOBD2 settings are optimal and the best for your car. Even the parameters are different for each vehicle, there might not be a need to make an additional adjustment.
EcoOBD2 will recognize your vehicle and your driving habits after around 200 km/150 miles driving, and then EcoOBD2 adjusts itself to match your car perfectly.

Installation and Calibration steps:
1 Pull the Car Key out from the ignition.
2 Find OBD2 connector(*) in your car and Plug in EcoOBD2
3 Insert the key into the ignition and twist the key to the first stage. (Do not start the car)
4 Press the reset button for about 5 sec. After releasing the button, just wait for a while about 30-54 sec. (EcoOBD2 will communicate and establish connection with ECU)
5 Start up the engine.
6 EcoOBD2 will recognize your vehicle and your driving habits, after around 200 km/150 miles driving and thus EcoOBD2 will adjust itself to match your car perfectly for more fuel saving.
Country USA
Brand JRTOOL
Color Green
EAN 7699055069686
Label JRTOOL
Manufacturer JRTOOL
MPN JRTOOL
PartNumber JRTOOL
Publisher JRTOOL
Studio JRTOOL
ReleaseDate 0000-00-00

Country	USA
Brand	JRTOOL
Color	Green
EAN	7699055069686
Label	JRTOOL
Manufacturer	JRTOOL
MPN	JRTOOL
PartNumber	JRTOOL
Publisher	JRTOOL
Studio	JRTOOL
ReleaseDate	0000-00-00

JRTOOL EcoOBD2 Plug and Drive EcoOBD2 Benzine Chip Tuning Box for Benzine 15% Fuel Save

You might also like...