Electronics > Computers & Accessories > Networking Products
PoE Texas MMF-RJ45 | Ethernet Cable Combiner/Splitter Kit - Use as a Pair to Combine Two Power and 10/100 Data (POE) Lines on One Ethernet - Mode A PoE Operation Only

PoE Texas MMF-RJ45 | Ethernet Cable Combiner/Splitter Kit - Use as a Pair to Combine Two Power and 10/100 Data (POE) Lines on One Ethernet - Mode A PoE Operation Only

Product ID: B01N806BN2 Condition: New
Sold Out

Product Description

PoE Texas MMF-RJ45 | Ethernet Cable Combiner/Splitter Kit - Use as a Pair to Combine Two Power and 10/100 Data (POE) Lines on One Ethernet - Mode A PoE Operation Only

FOR BEST RESULTS FOLLOW THESE STEPS CAREFULLY! (Check out the images above for examples)


Instructions for Dual LAN Installation:
1. Connect one of the two MMF-RJ45 adapters into two ports of your PoE or non-PoE switch This step is essential to get two lines of data and power on one cable!!
2. Run your Cat 5e or Cat-6 Ethernet cable up to 328 feet to the second MMF-RJ45 combiner/splitter
3. Plug each pigtail into the RJ45 on 2 separate devices (Use a coupler to extend the line if necessary)
NOTE: BOTH MMF-RJ45 splitters must be used to get two data or data and power lines

Specifications for dual LAN use

  • Long run connection 1 x 8P/8C RJ45 Female
  • Device/Switch Connector: 2 x 4P/4C RJ45 Male
  • Cable Rating: Cat 6
  • Max Speed Rating: 100Mb
  • 25 watts per circuit if CAT-6 is used
  • Uses two switch ports for one MMF-RJ45 combiner
  • Only 10/100 is supported over 2 pairs according to Ethernet standards

    Specifications for uPoE use

  • Use with an active PoE injector like AT-4 or AT-8 to provide up to 60 watts of power (Cisco devices negotiate on both Mode A and Mode B)
  • Combines two 802.3at ports into one uPoE port
  • Max Speed Rating: 100Mb in uPoE usage
  • Requires two ports on the PoE side of the AT-4 device
  • No splitter required at the remote device

    Follow these steps for uPoE application:
    1. Run one data cable to the female side of one MMF-RJ45 combiner/splitter
    2. Use two LAN ports on the Active PoE injector
    3. Use two PoE ports for the second MMF-RJ45 combiner/splitter
    4. Run your Cat6 Ethernet cable to the uPoE port on your Cisco device

    Important Notes
  • Cisco uPoE devices require auto-negotiation on Mode A and Mode B for application.
  • For 4-Pair PoE (4PPoE) some devices require passive power. For a passive PoE application, use our Mode A injector - GPOE-4A-48v120w

    • Technical Specifications

    Country
    USA
    Brand
    WiFi-Texas
    Manufacturer
    PoE Texas
    Binding
    Personal Computers
    ItemPartNumber
    MMF-RJ45
    Model
    8541545739
    UnitCount
    1
    UPCs
    722512407701
    EANs
    0722512407701

    You might also like

    Cable Matters RJ45 Splitter Ethernet Cable Share Kit in White 100 Mbps (Must Be Used in Pairs, One Unit On Each End of An Ethernet Cable Run)

    CERRXIAN RJ45 Female to 2 Female Splitter Coupler LAN Ethernet Network 1 to 2 Adapter (2-Pack)

    PoE Texas Power over Ethernet 12 volt 802.3af Splitters - Power any 12 volt device including IP cameras or Arduino at 330 ft with Data (Gigabit 12 volt 12 watt)

    UGREEN RJ45 Coupler 2 Pack in Line Coupler Cat7 Cat6 Cat5e Ethernet Cable Extender Adapter Female to Female (Black)

    2-Pack Active PoE power over ethernet Splitter Adapter 48V to 12V, IEEE 802.3af Compliant 10/100Mbps PoE Splitter With 12V output for Surveillance Camera, ipolex

    AC Infinity Vented Cantilever 1U Universal Rack Shelf, 14" Deep, for 19" equipment racks. Heavy-Duty 2.4mm Cold Rolled Steel, 60lbs Capacity

    BV-Tech 6 Port PoE+ Switch (4 PoE+ Ports with 2 Ethernet Uplink and Extend Function) - 60W - 802.3at + 1 High Power PoE Port

    (1-Pair)  RJ45 Splitter Adapter,SinLoon  Ethernet Cable Splitter Cat5, Cat5e, Cat6, Cat7,RJ45 Network Extension connector Ethernet Cable Sharing Kit with 2 PCS Cat6 Cable for Router TV BOX Camera PC L

    UGREEN RJ45 Coupler 5 Pack in Line Coupler Cat7 Cat6 Cat5e Ethernet Cable Extender Adapter Female to Female (Black)