STEPPERONLINE 5PCS Nema 17 Stepper Motor 1.5A 12V 45Ncm (63.74oz.in) 4-Lead 39mm Body W/ 1m Cable and Connector for DIY CNC/ 3D Printer/Extruder
Product Description
STEPPERONLINE 5PCS Nema 17 Stepper Motor 1.5A 12V 45Ncm (63.74oz.in) 4-Lead 39mm Body W/ 1m Cable and Connector for DIY CNC/ 3D Printer/Extruder
- 5 PCS, High torque Low noise
- Nema 17 stepper motor with step angle 1.8deg
- Holding Torque: 45Ncm(63.74oz.in), 12-24 VDC
- Rated Current/phase: 1.50A & Phase Resistance: 2.3ohms
- Build with 1m Pin Connector
This bipolar Nema 17 stepper motor with step angle 1.8deg and size 42x42x39mm. It has 4 wires, each phase draws current 1.5A, with holding torque 45Ncm (63.74oz.in).
Electrical Specification
*Manufacturer Part Number: 17HS15-1504S-X1
*Motor Type: Bipolar Stepper
*Step Angle: 1.8 deg
*Holding Torque: 45Ncm(63.74oz.in)
*Rated Current/phase: 1.50A
*Phase Resistance: 2.3ohms
*Inductance: 4.4mH ± 20%(1KHz)
Physical Specification
*Frame Size: 42 x 42mm
*Body Length: 39mm
*Shaft Diameter: Φ5mm
*Shaft Length: 24mm
*D-cut Length: 15mm
*Number of Leads: 4
*Lead Length: 1000mm
*Weight: 280g
Connection
Black(A+), Green(A-), Red(B+), Blue(B-)
Warning:
Make sure the motor connect to a constant current or chopper drive controller before you test motor.
Connecting the motor directly to a power supply will destroy the motor.
Technical Specifications
You might also like
KINGPRINT DRV8825 Stepper Motor Driver Module with Heat Sink for 3D Printer Rrerap Ramps 1.4 A4988 (Pack of 5pcs)
KeeYees 5M GT2 Timing Belt 6mm Width + 4pcs 20 Teeth 5mm Bore Belt Pulley Wheel + 4pcs Idler + 4pcs Tensioner Spring Torsion + 2pcs Gear Clamp Mount Block with Allen Wrench for 3D Printer RepRap
BIQU 3D Printer Part SKR V1.3 32bit Control Board Smoothieboard&Marlin Open Source Compatible with Ramps1.4/1.5/1.6 Support A4988/8825/TMC2208/TMC2100 Drivers
Sunhokey GT2 Black Aluminum 20 Teeth Timing Belt Idler Pulley for 3D Printer 6mm Width Timing Belt (Black-GT2 5mm Bore 20 Teeth)
BIQU A4988 Compatible Stepper StepStick Motor Diver Module with Heat Sink for 3D Printer Controller Ramps 1.4(Pack of 5pcs)
STEPPERONLINE Nema 17 Stepper Motor Bipolar 2A 59Ncm(84oz.in) 48mm Body 4-lead W/ 1m Cable and Connector compatible with 3D Printer/CNC
kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 (CNC Shield+UNO R3+Stepper Motor)
OctagonStar Flexible Couplings 5mm to 8mm NEMA 17 Shaft for RepRap 3D Printer or CNC Machine（2PCS）
STEPPERONLINE Short Body Nema 17 Bipolar Stepper Motor 1A 18.4oz.in/13Ncm DIY CNC Extruder
JIWINNER 12 pcs LM8UU Linear Bearings for 3D Printer