Smith's Original Clear Penetrating Epoxy Sealer™ [CPES] 2

Smith's Original Clear Penetrating Epoxy Sealer™ [CPES] 2 Pint - Warm Weather Formula (WW)
- - 1 to 1 mixing ration of Part A & Part B
- - Low Viscocity, made mostly from Resins
- - Extended Pot Life, so no rush or waste & Robust Shelf Life, Pro-Grade Longevity
- - Ultimate Cold-Weather Penetration : Bonds deep into wood, concrete, or masonry even below freezing-cures at temps as low as 25°F without cracking or bubbling.
- - Crystal-Clear Finish : Invisible protection that seals out moisture, rot, and stains while letting the natural grain shine through-no yellowing over time.
- - Super-Strong Durability : Penetrates up to 1/4 inch perfect defense against water, chemicals, and wear-perfect for decks, docks, or historic restorations.
- -Dries tack-free in 4-6 hours, full cure in 72, non-toxic ONCE cured.
- - Seals while still allowing the wood to breathe
- -Made in the USA
- - Manufactured in California
Dry Rot is the deterioration of wood caused by microscopic fungi feeding on the resins which bond the wood fibers together, leaving the fibers loose to crumble away. Smith's Original Clear Penetrating Epoxy Sealer (CPES) restores the wood by penetrating in and rebinding the wood fibers together, resolidifying it and impregnating the wood with epoxy resin so that it will be impervious to ever rotting again. Our revolutionary sealer - which is the original of its kind and still out-performs all of its imitators - restores dry rotted wood without the need to replace, and preserves new wood so that it will never rot. No other product comes close to the ability of Smith's CPES to penetrate and saturate wood. It is also an excellent primer, laminating the finish coat of paint or varnish down to the now preserved wood. ************************** The two formulas (Warm Weather/Cold Weather) are designated for temperatures at time of application. You may use Warm Weather Formula for temperatures between 50F and 110F. Cold Weather Formula may be used from 25F to 80F. ********************** The following are the six basic steps to restoring rotted wood: 1) Remove any old coatings, and dry the wood. 2) Clean off any very crumbly material. 3) Saturate the wood with Smith's Clear Penetrating Epoxy Sealer. 4) Once the solvents have evaporated, apply the Filler. 5) After 24 hours, sand Filler to shape. 6) Before painting, apply a light primer coat of the CPES. **********************To use the CPES as a primer/preservative on sound wood: 1) Saturate by brushing the CPES over the wood until it stops soaking in. 2) Let it fully cure. 3) Lightly sand any raised grain or drips. 4) Apply a light final application of the sealer. 5) Wait 24 hours and if the solvents have evaporated (you'll know by the smell being gone) then apply your first coat of finish. ************ CPES (Clear Penetrating Epoxy Sealer) and Smith's Epoxy Fill-it are sold on Amazon exclusively by TIMBERCRAFT.
Country USA
Brand SMITH & COMPANY CPES
Manufacturer TRIXES
Binding Misc.
ItemPartNumber CPESPCW
Color Clear
UnitCount 2
UPCs 185676000025
EANs 0185676000025
ReleaseDate 0000-00-00

Country	USA
Brand	SMITH & COMPANY CPES
Manufacturer	TRIXES
Binding	Misc.
ItemPartNumber	CPESPCW
Color	Clear
UnitCount	2
UPCs	185676000025
EANs	0185676000025
ReleaseDate	0000-00-00

Smith's Original Clear Penetrating Epoxy Sealer™ [CPES] 2 Pint - Warm Weather Formula (WW)

You might also like...