UCTRONICS ESP8266 Weather Station IoT Starter Kit for Arduino

UCTRONICS ESP8266 Weather Station IoT Starter Kit for Arduino IDE with ESP8266 ESP-12E Development Board 0.96" OLED Display and DHT11 Temperature and Humidity Sensor
- The UCTRONICS ESP8266 Weather Station IoT Starter Kit includes an ESP8266 ESP-12E Development Board, a 0.96" OLED display, a DHT11 Temperature and Humidity Sensor, 40x10cm female-female jumpers, a USB cable as well as a UCTRONICS user guide (link for download), the breadboard shown in the picture is not included
- Developer-friendly module ESP8266 come with a USB connector and the maximum number of available pins. ESP8266 full IO mouth leads directly download without reset
- The 0.96" 128x64 pixel OLED display supports I2C, wide viewing angle, low power consumption and high response speed
- DHT11 Temperature and Humidity Sensor with characteristics humidity measurement range: 20~90% RH, humidity measurement accuracy: +/-5% RH, temperature measurement range: 0~50°C, temperature measurement accuracy: +/-2°C
- UCTRONICS ESP8266 Weather Station IoT Starter Kit gets the current and forecast weather information from an online service and displays the expected conditions on a 128X64 pixels OLED display with nice icons. The program uses a side scrolling carousel to display the date, time. In addition, it displays the information about 3-day forecast temperature and humidity through DHT11 sensor. Contact us through Buyer-Seller Messages for further help.
Name: UCTRONICS ESP8266 Weather Station IoT Starter Kit
Specification:
ESP8266 ESP-12E Development Board
802.11 b/g/n protocol
Wi-Fi Direct (P2P), soft-AP
Integrated TCP/IP protocol stack
Integrated TR switch, balun, LNA, power amplifier and matching network
Integrated PLL, regulators, and power management units
+19.5dBm output power in 802.11b mode
Integrated temperature sensor
Supports antenna diversity
Power down leakage current of < 10uA
Integrated low power 32-bit CPU could be used as application processor
SDIO 2.0, SPI, UART
STBC, 1x1 MIMO, 2x1 MIMO
A-MPDU & A-MSDU aggregation & 0.4 s guard interval
Wake up and transmit packets in < 2ms
Standby power consumption of < 1.0mW (DTIM3)

0.96" 128x64 pixel OLED display
Size: 0.96''
Resolution: 128X64
Supported platforms: for Arduino, ESP series, 51 series, MSP430 series, STIM32 / 2, SCR chips
Driver IC: SSD1306
Communication: IIC
VCC: 3.3~5V
GND: Ground
SCL: Serial Clock
SDA: Serial Data

DHT11 Temperature and Humidity Sensor
Digital signal output
VCC: 3.3V~5V
GND: Ground
DATA: MCU IO port
Tips: Do not reverse the VCC and GND, otherwise it will burn!

Package including:
1pcs ESP8266 ESP-12E Development Board
1pcs 0.96" OLED display
1pcs DHT11 Temperature and Humidity Sensor
1pcs 40x10cm female-female jumpers
1pcs USB cable

Note:
For the free weather API restriction issue, we have updated the user manual online, contact us for the newer version.
Country USA
Brand UCTRONICS
Manufacturer UCTRONICS
Binding Electronics
ItemPartNumber K0061
Model K0061
ReleaseDate 0000-00-00

Country	USA
Brand	UCTRONICS
Manufacturer	UCTRONICS
Binding	Electronics
ItemPartNumber	K0061
Model	K0061
ReleaseDate	0000-00-00

UCTRONICS ESP8266 Weather Station IoT Starter Kit for Arduino IDE with ESP8266 ESP-12E Development Board 0.96" OLED Display and DHT11 Temperature and Humidity Sensor

You might also like...