PTE™ Wire Tracer & Circuit Tester -Tone Generator & Probe

PTE™ Wire Tracer & Circuit Tester -Tone Generator & Probe Kit - Find & Trace Wires & Cables, Test Circuit Continuity, Network Telephone Line, Coaxial, Automotive - Features Alligator Clips & RJ11 Plug
- FIND WIRES QUICKLY AND ACCURATELY - Detect wires in a range of applications including buried wires, single strand, broken wires, etc. Not meant for live electrical wires. Suitable for Electrical wires, Landlines, Coaxial cables, Automotive cables etc...
- MAXIMIZE TRACING ACCURACY - Wall thickness and material can affect signal transmission. While the Tone signal can track cables through ceilings, floors, and walls, performance may vary. (IMPORTANT: For best results, use only one alligator clip in Tone Mode.)
- DETECTS SHORT/OPEN CIRCUIT/ TELEPHONE LINE - Thanks to the CONT mode, you can check for short and open circuits, and the RJ11 connector lets you test telephone systems easily (Use both Alligator clips in Continued Mode)
- ADJUSTABLE SENSITIVITY - The variable sensitivity dial allows you to identify a single wire when multiple wires are routed in close proximity, ensuring precision and safety while avoiding false detection
- ONE-YEAR WARRANTY - Should you experience any issues with the product, please refer to the instructions below or contact the seller, TrueToSource, via Amazon messaging for troubleshooting assistance or to request a replacement.
This Wire Tracer and Circuit Tester - including a sender/tone generator and a detector - is designed to identify and trace wires or cables without damaging the insulation.

Note: Requires 2 9V batteries (not included)

Use as a Wire Tracer
Connect only one of the alligator clips of the tone generator to your wire and use the probe to follow the wire along, or ID it at the other end. Use the probe's volume control to adjust sensitivity. The audible tone will increase in volume as the probe gets closer to the wire. You can even use it to trace a single wire. Find broken wires buried in the ground or in walls. (Detection limit will vary depending on material between wire and probe. Swap tone generator for a more powerful signal source as needed.)

Use as Circuit Tester
Connect two alligator clips to the ends of the wire to check if resistance exists. If yes, the wire could be a short or open circuit. You can then use the Wire Tracer function to locate the problem.

Telephone line maintenance
For telephone lines, the Wire Tracer and Circuit Tester can identify Tip and Ring lines and determine the status of the line - clear, busy, or ringing - making it more convenient to maintain telephone lines.

Specifications
- Maximum length of cable tested: Allows for sending tone up to 328 feet / 100 m
- Frequency: 1.1 to 1.4 kHz output for Sender; detects above 30 Hz for Detector
- Power: 2 x 9V batteries (not included)
- Dimensions and Weight: Sender: 2.8 x 2.6 x 1.2 inch / 7 x 6.5 x 3 cm ; 3 oz / 85g; Detector: 8.5 x 2 x 1.4 inch / 21.5 x 5 x 3.5 cm; 3.3 oz / 95g

Note: Do NOT connect to a live circuit. Detector probe can be used with live circuits but should NOT be allowed to touch a live wire in any circumstance.

Packaging Contents
Detector, sender with RJ-11 plug and 2 alligator clips, manual (batteries not included)
Country USA
Brand PTE
Manufacturer PTE
Binding Misc.
ItemPartNumber 6503
Model 6503
Color Clear
UPCs 767654080108
EANs 0767654080108
ReleaseDate 0000-00-00

Country	USA
Brand	PTE
Manufacturer	PTE
Binding	Misc.
ItemPartNumber	6503
Model	6503
Color	Clear
UPCs	767654080108
EANs	0767654080108
ReleaseDate	0000-00-00

PTE™ Wire Tracer & Circuit Tester -Tone Generator & Probe Kit - Find & Trace Wires & Cables, Test Circuit Continuity, Network Telephone Line, Coaxial, Automotive - Features Alligator Clips & RJ11 Plug

You might also like...